top of page
Ultraviolet Systems

Ultraviolet Systems

  • EXPLANATION

    Disinfection with Aqualine Ultraviolet Systems is the process of neutralizing microorganisms without adding any chemicals or oxidants to the water.

    Disinfection with Ultraviolet Systems is the process of neutralizing microorganisms without adding any chemicals or oxidants to the water. Thanks to the ultraviolet lamp placed in a tube-like glass case, the water entering the device is given a dosed UV light. This is ultraviolet  The rays cause the microorganisms to become ineffective by disrupting their DNA structure. In this way the average   Disinfection efficiency of 99.9% is achieved.
    In order for microorganisms to be killed with this system, ultraviolet light must hit them directly. Therefore, before the water enters the Ultraviolet system, parameters such as sediment and turbidity must be removed from the water. For this, it is recommended to use a sand filter or a cartridge filter before ultraviolet.
    Another issue to be considered in Ultraviolet Systems is to put the system as close to final use as possible. In addition, the water coming out of the system should not enter a separate unit, especially open to the atmosphere, and should be used without waiting. Periodic maintenance is important to obtain a good efficiency in ultraviolet units. Quartz glass cleaning should be done periodically depending on the UV lamp change and raw water quality once a year. If this cleaning is not done, UV radiation efficiency will decrease and device efficiency will decrease.

    ADVANTAGES OF ULTRAVIOLET SYSTEMS
     

    • Its application is simple.
    • It has high disinfection ability.
    • It does not form by-products and residual substances in water.
    • It does not affect the taste of the water.
    • There is no formation of corrosive substance.
    • It is economical.

     

    STANDARD FEATURES OF ULTRAVIOLET E SERIES SYSTEMS
     

    • Body 304 quality stainless steel
    • Power supply 220 V 50 Hz
    • Working pressure 8 Bar
    • Lamp life 9000 Hours
    • Operating temperature 2-40 oC
    • Connection type is produced as Nipple (External Threaded).
    • Lamp macra FIRSTLIGHT  ( ISO 9001 certified)
    • ES series control board features
    • In our ES Series devices, the Control Panel is separate from the device body.
    • Hour Meter, Fault Indicator LED is available. (Excluding E 50 UV.)

     

    STANDARD FEATURES OF ULTRAVIOLET ES SERIES SYSTEMS
     

    • Body 304 quality stainless steel
    • Power supply 220 V 50 Hz
    • Working pressure 8 Bar
    • Lamp life 9000 Hours
    • Operating temperature 2-40 oC
    • Connection type is produced as Flange and Nipple (External Threaded).
    • lamp brand  FIRSTLIGHT ( ISO 9001 certified)
    • ES series control board features
    • In our ES Series devices, the Control Panel is separate from the device body. There are Hour Meter, Energy Indicator Led, Separate Fault Indicator Led for each lamp and fault notification audible alarm systems. 

     

    DESIGN CRITERIA

     

    • In all designs, the AKM value is assumed to be less than 50 mg/l and the design is made with 0.9 mm Fiber.
    • Production flow rates 15 NTU Turbidity 3mg/l DOC  for well water. For different turbidity values, the feed pump capacity will be changed, so the production flow rates will change. Operation and BW times, dosage times will be adjusted according to water analysis when the system is commissioned. 
    • For the selection of chemical dosing pumps, 250 mg/l CaCO3 alkalinity value, 1000 us/cm conductivity, and 20 degrees water temperature are accepted. Pumps are selected according to pH 2,5 - ph 12.
    • The minimum feed flow and pressure required for all devices are given in the table.
    • Compact St-37 epoxy painted carbon steel chassis will be for UF160, 260, 360 series.
    • Track UF chassis for UF460, 660, 860, 1060 series + St-37 epoxy painted carbon steel chassis for surface piping.
    • Gray water Aqualine UF series will be supplied with SS304 stainless steel compact chassis.
    • It is accepted that UF product water tank will be used for the backwash tank in all devices.
    • Required minimum tank volumes are indicated in the table. Stainless steel backwash pumps are included in the price. The product water tank is customer supply.
    • PN10 PVC piping is used in all systems.
    • Automatic valves will be electrically actuated.       
    • Product water flow meters will be inlene type.
    • Glycerin manometers will be used.
    • Chemical dosing pumps SEKO brand will be used.
    • PLC controller will be used in Aqauline Professional and Gray Water devices. (Operator panel is optional.)
    • In case of washing the UF modules, manual washing systems are optionally priced.

For detailed information about the product, a price offer for your projects and your questions

whatsapp-logo-.png

CLICK to review and download product documents in pdf format

adobe-pdf-logo-1480D328A9-seeklogo.com.p
bottom of page